Screws and bolts: what’s the difference?
The simple rule, used by the engineers’ reference Machinery’s Handbook, is about how the fastener is tightened. A bolt passes through holes in the parts and is held by turning a nut. A screw goes into a thread in the material, either one that is already there or one it cuts itself, and is tightened by turning its head [2]. In everyday use the names overlap a lot: a “lag bolt” is really a large wood screw, and in the UK it is called a coach screw [2].
Bolt Depot, a US fastener supplier, produced the reference chart above to help people identify what they have in their hand [1]. It covers 19 types of screws and bolts, 10 head styles, 7 drive types, 9 washers and 16 nuts. This guide explains the main ones and when to use each.
Types of screws
- Wood screws have a smooth, unthreaded shank below the head and a tapered point. The plain shank lets the top piece of wood pull tight against the bottom one [1].
- Sheet metal screws are threaded all the way to the head, with a sharp point for thin metal, plastic and similar materials [1]. Self-drilling versions have a drill-bit tip so you don’t need a pilot hole.
- Machine screws have a uniform thread for use with a nut or a tapped (pre-threaded) hole. Thread-cutting machine screws have a point that cuts its own thread [1].
- Socket screws (Allen head) are turned with a hex key and are common in machinery and flat-pack furniture [1].
- Set screws have no head. They screw fully into a threaded hole, typically to lock a pulley or knob onto a shaft [1].
- Lag screws (lag bolts, coach screws) are heavy wood screws with a hex head, used for wooden framing, decks and fixing machinery to wooden floors [1][2].
- Hanger bolts have a wood thread on one end and a machine thread on the other, so you can screw them into wood and then fix something on with a nut [1].
Types of bolts
- Hex bolts have a six-sided head and a machine thread for a nut or tapped hole. They are the standard general-purpose bolt [1].
- Carriage bolts (coach bolts in the UK) have a smooth domed head with a square section underneath that grips the wood and stops the bolt turning while you tighten the nut [1].
- Eye bolts have a ring on the end for rope or chain; eye lags are the same with a wood thread [1].
- J-bolts and U-bolts are bent shapes for tie-downs, anchoring into concrete and clamping round pipes [1].
- Shoulder bolts (stripper bolts) have a smooth, precise shoulder that acts as a pivot or axle [1].
- Elevator bolts have a large flat head that sits flush, often used in conveyor belts [1].
- Sex bolts (barrel nuts or Chicago bolts) have an internal thread and pair with a mating screw, giving a finished head on both sides of the joint, as in binders and some furniture [1].
Screw head types
Head shape decides how the fastener sits on the surface [1]:
| Head | Shape | Typical use |
|---|---|---|
| Flat (FH) | Countersunk, flat top | Sits flush with the surface, in wood and countersunk holes |
| Oval (OH) | Countersunk, rounded top | Decorative flush finish, often with a finishing washer |
| Pan (PN) | Slightly rounded, short vertical sides | General use where the head can sit proud |
| Truss | Extra wide, low rounded top | Spreading load on thin or soft material |
| Round (RH) | Domed | Older general-purpose screws |
| Hex and hex washer | Six-sided, sometimes with built-in washer | Turned with a spanner or socket for higher torque |
| Socket cap and button | Cylindrical or low dome, hex socket | Machinery, tight spaces, neat finish |
Screw drive types
- Slotted: the original single slot. Easy to make but the screwdriver slips out easily [1][3].
- Phillips: the cross recess was developed to solve slotted screws’ problems, including slipping and difficulty with powered tools [3]. Bolt Depot’s older chart groups Phillips with Frearson, but they are different: a Frearson recess has a sharper point and needs its own driver [3].
- Pozidriv: looks like Phillips with extra small lines. A Phillips driver will turn it but may damage tight screws, and a Pozidriv driver damages Phillips screws [3]. Pozidriv is the common cross head on UK and European wood screws.
- Square (Robertson): a square socket with a slight taper that holds the screw on the driver tip [3].
- Hex socket (Allen): patented in Germany in 1936 by Bauer and Schaurte, which is why it is called “inbus” in German [3].
- Torx: a six-pointed star, designed for higher torque transfer and less slipping [3].
- One-way: goes in with a normal slotted driver but needs a special tool to remove, for security [1].
Types of washers and nuts
A flat washer spreads load under a nut or head; a fender washer is an oversized one for soft materials. Split lock and tooth lock washers help stop nuts and bolts working loose [1].
The standard hex nut covers most jobs. A nylon insert lock nut (Nyloc) has a plastic ring that grips the thread and resists vibration. Jam nuts are thin nuts used in pairs to lock each other. Wing nuts are tightened by hand, acorn or cap nuts cover a sharp bolt end, tee nuts are hammered into wood to create a threaded hole, and castle and slotted nuts take a split pin through a drilled bolt so they cannot come undone [1].
How to choose the right screw or bolt
- Wood to wood: wood screws, or lag screws for heavy loads. Use outdoor-rated coated or stainless screws for decks.
- Into thin metal: sheet metal or self-drilling screws [1].
- Metal to metal, or anything you may take apart: a bolt or machine screw with a nut and washer.
- Something that vibrates: add a lock washer or nylon insert lock nut [1].
- A neat flush finish: a countersunk flat or oval head.
Thread standards matter too. Most of the world uses ISO metric threads, while the US also uses the Unified (inch) standard; the two were both defined in the late 1940s and do not interchange [2].
Questions about types of screws and bolts
What is the difference between a screw and a bolt?
By the Machinery’s Handbook definition, a bolt is tightened by turning a nut, and a screw is tightened by turning its head into a thread [2].
What is the difference between a wood screw and a sheet metal screw?
A wood screw has a smooth shank below the head and a tapered point. A sheet metal screw is threaded right up to the head [1].
Is a lag screw the same as a wood screw?
It is a large, heavy-duty wood screw, usually with a hex head. It is also called a lag bolt, or a coach screw in the UK [2].
What are the main types of bolts?
Hex bolts, carriage bolts, eye bolts, U-bolts, J-bolts, shoulder bolts, elevator bolts and sex bolts are the most common [1].
Can I use a Phillips screwdriver on a Pozidriv screw?
It will usually turn, but it can slip and damage a tight screw. Use the matching driver where you can [3].
Sources
- Bolt Depot, Fastener Type Chart, the creator’s page for this chart.
- Wikipedia, Screw.
- Wikipedia, List of screw drives.
Last reviewed 2 November 2026


